ABOUT

Solutions & Cases

Our Case
  • Ball End Mills (Ball Nose) Carbide Cobalt & HSS

    End Mills > Ball Nose End Mills. Ball End Mills. A ball end milling cutter is also known as a "ball nose mill". The end of this tool is ground with a full radius equal to half of the tool diameter, and the edges are center cutting. They can be single end or double end and they can be made from solid carbide or various compositions of high speed

  • 2 Flute BALL NOSE Carbide Mill (for 3D Carving) End Mills

    A favourite of CNC enthusiasts is to 3D carve and a ball nose router bit allows you to do just that. These are a great entry level bits as the are value for money compared to tapered ball nose. The radius = 1/2 of the diameter with no flat bottom. These bits can also be used to engrave lettering. Suitable for. Plastics (ABS, acrylic, HPDE etc.)

  • Two Flute-Ball End-Straight Fluted Carbide End Mills

    Home > Carbide End Mills > Straight Fluted End Mills >Single End Ball > 2 Flutes. Two Flute-Ball End-Straight Fluted Carbide End MillsBall end mills with two straight flutes are single ended, have two cutting edges, and have a zero degree helix. They are used to mill plastics, composites of epoxy and glass, and are also used for special profile milling applications where a full radius is required.

  • Ball-Nose End Mills McMaster-Carr

    Variable spacing between the flutes reduces vibration, allowing these end mills to Offering two times the life of a standard carbide end mill, the end mills in these sets have two milling ends so you can switch to the opposite end when one end wears out. Made of solid carbide, they're harder, stronger, and more wear resistant than high-speed steel for the longest life and best finish on

  • 2 Flute Carbide End Mill For Alu Uncoated Arc Euro Trade

    2 Flute Carbide End Mill For Aluminium Standard Length The smaller grain size of Micro-Grain Carbide makes it possible to grind a sharper cutting edge. Close. × 2 Flute End Mill. Used for: General milling operations; Two flute end mills have a larger flute volume and therefore a higher chip carrying capacity. Suitable for higher stock removal rates where finish is not critical. These

  • Ball End Mills (Carbide) Carbide Ball End Mills MISUMI

    MSB230 MUGEN-COATING 2-Flute Ball End Mill. Union Tool Carbide 2-Flute Ball-End Mill. TSC Series Carbide Ball End Mill, Short Model. TSC Series Carbide Ball End Mill for High-Hardness Steel Machining, 3-Flute/Regular Model. GS MILL Hard Ball GSBH. 2-Flute, Ball End, Miniature Type FX-MG-EBD-3. 2-Flute Ball End Type CBN-EBD

  • End Mill Series MITSUBISHI MATERIALS CORPORATION

    Ball nose, Short cut length, 2 flute, Strong geometry type, Long shank 11 different sizes available. Overhang Cutting length (m) Competitor A Chipping Competitor B Chipping No Damage End mill Workpiece Revolution Feed rate Machining method Air blow Higher feed rates and 4 times longer tool life compared to competitor end mills ! Ball nose, 3

  • Ball-Nose End Mills McMaster-Carr

    Variable spacing between the flutes reduces vibration, allowing these end mills to Offering two times the life of a standard carbide end mill, the end mills in these sets have two milling ends so you can switch to the opposite end when one end wears out. Made of solid carbide, they're harder, stronger, and more wear resistant than high-speed steel for the longest life and best finish on

  • 2 Flute Carbide End Mill For Alu Uncoated Arc Euro

    2 Flute Carbide End Mill For Aluminium Standard Length The smaller grain size of Micro-Grain Carbide makes it possible to grind a sharper cutting edge. Close. × 2 Flute End Mill. Used for: General milling operations; Two flute end mills have a larger flute volume and therefore a higher chip carrying capacity. Suitable for higher stock removal rates where finish is not critical. These

  • Carbide ball nose end mill R0.3mm 2 flute ball nose end

    Milling Type: Ball nose end mill, Spherical 2 flutes ball nose carbide end mill Specification: Dia 0.6mm*cutting length 1.5mm*flute length 10mm*shank dia 3.0*total length 45mm (metric or inch 1/2" 1/4" 1/8" 1/12" available)

  • 2 Flute Long Neck Carbide Ball Nose End Mills 55HRC [2

    2 Flute Long Neck Carbide Ball Nose End Mills 55HRC. 2 Flute Long Neck Carbide Ball Nose End Mills 0.5µm Micro-grain Carbide AlTiN Coated for General Use on materials up to 55-58HRC, performs well on Cast Iron, Copper, Mould Tool and Die Steel, 304 Stainless

  • End Mill Series MITSUBISHI MATERIALS CORPORATION

    Ball nose, Short cut length, 2 flute, Strong geometry type, Long shank 11 different sizes available. Overhang Cutting length (m) Competitor A Chipping Competitor B Chipping No Damage End mill Workpiece Revolution Feed rate Machining method Air blow Higher feed rates and 4 times longer tool life compared to competitor end mills ! Ball nose, 3

  • Two-Flute End Mills McMaster-Carr

    When one end wears out, switch to the opposite end for two times the life of a standard carbide end mill. Made of solid carbide, these end mills are harder, stronger, and more wear resistant than high-speed steel for the longest life and best finish on hard material.

  • Solid Carbide End Mills China Manufacturer & Suppliers

    25/12/2020· Solid Carbide End Mills. Square End Mills 2 Flute; Square End Mills 4 Flute; Ball Nose End Mills 2 Flute; Ball Nose End Mills 4 Flute; Corner Radius End Mills 4 Flute; Micro square endmill (hrc55) Micro Ballnose endmill (hrc55) End Mill For Aluminum. 2 Flute End Mill For Alu; 3 Flute End Mill For Alu; Ballnose Endmill for Aluminum (hrc45 hrc55

  • Carbide & HSS End Mill in 2, 3 & 4 flute for Slot

    We stock a wide range of milling bits for your job from 2 flute, 3 flute, 4 flute and ball nose. Wondering what number flute to use? Don't know if to buy HSS or a Carbide cutter with what coating? Here is a bit of a breakdown. Sort By: Quick view Choose Options. 1 Flute UP CUT End Mill (for Aluminium) $10.95 $23.95. Quick view Choose Options. 2 Flute BALL NOSE Carbide Mill TiAlN HRC 45. $6

  • Micro Machining Solid Carbide End Mills Secotools

    One site. Everything SECO.

  • 4 FLUTE CARBIDE BALL NOSE END MILLS

    4 flute carbide ball nose end mills, uncoated. 11/32 dia., 4 flute solid carbide ballnose endmill 1.0 loc, 3/8 shank, 2.5 oal, uncoated