ABOUT

Solutions & Cases

Our Case
  • Cone Crusher Shaft Broken Crushing, Screening

    Cone Crusher Shaft Broken (2 replies) S. [email protected] 7 months ago. [email protected] 7 months ago. Hello, The shaft in question is very similar to the peter&x GP100S and the shaft has broken as in the attached picture. The vitals were good and the crusher was beginning to give some odd sounds before the operator found that the shaft was broken. Any expert advice on how to proceed failure analysis

  • Treatment method of broken shaft of scrap crusher

    Treatment method of broken shaft of scrap crusher. In the long-term operation of the scrap crusher, there are generally three reasons for the main shaft break: spindle quality problems, external influence factors, and spindle fatigue fracture. For the first two, according to the actual situation to select the appropriate spindle material, to ensure the normal external factors, you can avoid

  • How To Repair The Broken Shaft Of Cone Crusher?

    Cone crusher is the commonly used crushing equipment. During its production process, the broken of shaft is a kind of common fault. ball mill processing gold The frequent broken of shaft will not only affect the normal production of cone crushing machine, but also increase its daily maintenance and repairing work. SBM Machinery will analyze the causes and solutions of this failure in the

  • 14 Cone Crusher Common Problems And How To Fix Them

    22/07/2019· 3. It may be the eccentric shaft problem, the eccentric shaft fixed bushing loose or falling will lead to no gap between the bearing housing and the frame, resulting in the eccentric shaft can not operate, so the cone crusher will stop suddenly. 4. Is the belt tightness is not enough, the belt is too loose will make the belt skid, can not

  • Analysis of Common Failures and Causes of Cone Crusher

    The temperature of the bush at the moving cone and the eccentric shaft also rises sharply; the splash of lubricating oil inside the machine is thrown around, and the lubrication condition is deteriorated; the water seal is broken, and water in the fuel tank. "Flying car" failure will cause the crusher to vibrate strongly, the main shaft to be hugged, and tile breaking.

  • The Most Practical Jaw Crusher Repair and Maintenance

    11/03/2021· hole, flat, cracks on jaw crusher plate Pitman bearing broken Although the main crushing process is complemented by jaw plates, the crucial parts that give a motion to the moveable jaw plate are toggle plate, pitman bearing and flywheel. The pitman drives the moveable jaw dies to push stone material towards stationary jaws, which would create strong pressing forces to both jaw dies.

  • Crusher broken stone machine selection and maintenance

    26/07/2011· The broken line than the allocation to be reasonable, so as to maximize the efficiency of crushing machine. Spring pressure is not too tight, too much pressure will be off-axis incident occurred, the pressure is too small spring would frequently beat, impact crusher works, and the product size thicker. Oil temperature is not too high or too low, otherwise it will affect the machine operation.

  • Cause Analysis and Problems Solving of Jaw Crusher HXJQ

    10/12/2019· The eccentric shaft is bent or broken. Cause analysis: 1 Rollover occurs during the lifting process of the mainframe machine, so that the eccentric shaft is bent by one side. 2 The hardness of the crushed material exceeds the specifications of the product manual. 3 The machine is overloading. 4 The brackets do not conform to the standard, and it is self-broken when the non-crushed objects

  • Treatment method of broken shaft of scrap crusher

    Treatment method of broken shaft of scrap crusher. In the long-term operation of the scrap crusher, there are generally three reasons for the main shaft break: spindle quality problems, external influence factors, and spindle fatigue fracture. For the first two, according to the actual situation to select the appropriate spindle material, to ensure the normal external factors, you can avoid

  • 14 Cone Crusher Common Problems And How To Fix

    3. It may be the eccentric shaft problem, the eccentric shaft fixed bushing loose or falling will lead to no gap between the bearing housing and the frame, resulting in the eccentric shaft can not operate, so the cone crusher will stop suddenly. 4. Is the belt tightness is not enough, the belt is too loose will make the belt skid, can not

  • Cause Analysis and Problems Solving of Jaw Crusher

    10/12/2019· The eccentric shaft is bent or broken. Cause analysis: 1 Rollover occurs during the lifting process of the mainframe machine, so that the eccentric shaft is bent by one side. 2 The hardness of the crushed material exceeds the specifications of the product manual. 3 The machine is overloading. 4 The brackets do not conform to the standard, and it is self-broken when the non-crushed objects

  • what can cause a cone crusher motor s shaft to be broken

    S Series Cone Crusher China Cone Crusher Machine. The working principle of s cone crusher is very complex when the spring cone crusher is at work, the eccentric shaft is rotated through a horizontal axis and a pair of bevel gears the crushing cone shaft is forced to swing by the eccentric sleeve the broken wall surface to or from the rolling mortar wall now and make in the crushing cavity

  • P&Q University Lesson 7- Crushing & Secondary Breaking

    02/09/2019· The vertical shaft impact crusher (or VSI) has a rotating shaft that runs vertically through the crushing chamber. In a standard configuration, the VSI’s shaft is outfitted with wear-resistant shoes that catch and throw the feed stone against anvils that line the outside of the crushing chamber. The force of the impact, from the stone striking the shoes and anvils, fractures it along its

  • Gyratory Crusher an overview ScienceDirect Topics

    The first shaft is a pivoting shaft on the top of the crusher, while the other is an eccentric shaft that drives both toggle plates. The moving jaw has a pure reciprocating motion toward the fixed jaw. The crushing force is doubled compared to single toggle crushers and it can crush very hard ores. The jaw crusher is reliable and robust and therefore quite popular in primary crushing plants

  • 4 Types of Stone Crushers' Maintenance and Efficient

    22/04/2021· Horizontal Shaft Impact crusher (HSI) Impact crusher working animation The working principle of impact crusher is that the spinning rotor under the driving of the motor can genetate strong impact force which make blow bars crush stone material into small pieces. Then the crushed material would be thrown by hammers towards, which makes another crushing process "stone to stone".

  • Crushers QueensMineDesignWiki

    In classic mine design, the crusher is located near the shaft. This has the advantage that the material can go directly from the crusher to the skip. For mine operations that use truck haulage, the extra travel distance for the trucks is compensated by the advantages of more rapid access for excavation of the crusher and the expenses involved in moving the crusher (de la Vergne, 2003). Under

  • Rock Crusher- Jaw& Cone Rock Crushing Machine

    The type of rock crusher for sale is mainly composed of frame, rock crusher transmission shaft, eccentric sleeve, spherical bearing, crushing cone, adjusting device, adjusting sleeve, spring and discharging port. In order to give customers a better understanding of the crusher, Aimix will describe the detailed informations of the following parts . Firstly, the main frame of the rock crushing

  • Rotor centrifugal crusher Selective crusher with a

    Specialized in vertical shaft crushers (rotor and vertical shaft impact crushers) Patented twin-chamber rotor ; Unit ready for operation. Ready-to-install unit consisting of machine and drive train on a base frame; Easy access due to large cover that can be raised hydraulically and pivoted by 360° Reliable greasing. Recirculating oil lubrication with cooling and integrated monitoring ensures