ABOUT

Solutions & Cases

Our Case
  • How to restore a rusted wrought iron pot stand Hometalk

    18/12/2017· Sand the rust off,clean and spray paint with Rustoleums 2X for metal.If going outside seal with a UV clear waterproof sealer. Lisa S. on Dec 18, 2017 If it small scrub down with steel wool pads. Sand. Then prime and paint.

  • How to Paint Metal Plant Stands eHow

    Prepare your plant stand for paint by first washing it with a mild detergent and water mix. Then using a wire brush remove any loose paint and rust. Use your sandpaper to smooth any surface conditions. Rinse your plant stand and allow it to dry completely.

  • How to Seal an Iron Planter Home Guides SF Gate

    Sand the cast iron surface with coarse 60-grit sandpaper to remove heavy rust. Coarse-grit sandpaper removes surface rust and often scratches the cast iron surface, so it is necessary to sand the...

  • How To Quickly Update A Plant Stand Table Interior

    Shake the can for around a minute before use and often during use. Hold the can around 10-12 inches from the surface. Spray lightly in a back and forth motion in long steady strokes.

  • Plant Stand Design Ideas || Wrought Iron Plant Rack

    14/10/2020· Hi guys! In today's video I have some amazing wrought iron plant stand and rack design ideas for your indoor and outdoor garden space. Hope you enjoy.. If yo...

  • How to Restore Rusty Wrought Iron Hunker

    Sand the wrought iron with sandpaper to further remove rust. Use the sandpaper to also remove any flaking or loose paint. Begin by using a coarse sandpaper to remove deeper rust. Go over the wrought iron with a medium-grit sandpaper.

  • 36 DIY Plant Stand Ideas: How To Make A Plant Shelf

    This is a simple plant stand that costs less or no money to make at all, the creator used some hanger, cement, sand, and a few low-cost materials to make the plant stand. 3. DIY Cheap Plant Stand. This is a new and improved way of making a plant stand that is cheap and sturdy. Depending on the space you have to place your plant stand, you’ll need wood and a few other essential materials. 4

  • How to Sand Blast (with Pictures) wikiHow

    29/03/2019· Use plastic or a soda abrasive around sensitive areas. For areas that are made of plastic or have electrical components, use a light abrasive. While these media work slower, they are more gentle to the material and will not damage the surface. Plastic beads are reusable if you use them in a

  • 13 Free DIY Plant Stand Plans The Spruce Crafts

    21/10/2020· A raw edge concrete round sits on top of stained and painted dowels for this free plant stand plan. The plan takes you through each step, including making the concrete round for the top. If you like this look, check out these DIY concrete planters . Raw Edge Concrete Plant Stand

  • 15 Creative DIY Plant Stand Ideas Garden Lovers Club

    Snuggle a single potted plant into a well-fitting plant stand to add focus and a sense of importance to the specific plant of your choosing. A single-potted DIY stand can be made from virtually anything. Opt for plants that provide a sense of intensity and stand out from the rest of the plants in your home. Check out The Sorry Girls for a

  • How To: Strip and repaint wrought-iron furniture The

    05/02/2014· He agreed with your hunch that enamel paint should stand up fine indoors, though for exterior use he would recommend powder coating, a solvent-free process that uses electrostatic charge to

  • How To Clean Wrought Iron Furniture and Railings

    16/02/2021· Wrought iron is a beautiful and durable material when used for outdoor furniture, railings, and ornamental accessories, as well as for indoor accents, such as shelves, brackets, and fixtures.Because the texture is somewhat rough, wrought iron tends to collect dust and grime a little more readily than smooth surfaces, but when painted and maintained properly, cleaning is quite easy.

  • Wrought Iron Flower Plant Stands A Rustic Garden

    Our 5 most popular plant stands are: 1. Country Style Fern Stand, 2. Wrought Iron Square Round Urn Plant Stand, 3. 34" Deep Basket Plant Stand, 4. Scalloped Fernery Plant Stand and 5. The 30" Curl Fernery Plant Stand

  • 10 Indoor Plant Stands that Seriously Stand Out

    07/12/2020· In lieu of traditional wicker or wrought iron structures to display plants, designers have—pardon the pun—sprouted beautiful, modern plant stands to not only hold your plant

  • Sand Casting Metal Casting Resources

    Sand casting is a process that utilizes non-reusable sand molds to form metal castings. On one hand, casting is a deceptively simple manufacturing process: anyone who has formed castles at the beach knows sand can be used to make detailed shapes. However in a foundry, dealing with the heat of molten metal, many factors must be considered for success. Casting is used to make metal components of

  • 42 Unique, Decorative Plant Stands For Indoor &

    Elevate your indoor and outdoor plants with our top picks for planter pots and stands. Choose from metal, iron, ceramic, hanging, mesh and wooden finishes.